亚游国际ag-亚游首页登录入口

Hotline:13775442299
PVC plastic template

Contact

Jiangsu Wangke New materials Co., Ltd. 

Contact: Manager Wang. 

Mobile phone: 13141505998. 

Contact: manager Li. 

Mobile phone: 13775442299. 

Tel: 0518 81183228. 

Fax: 0518 81183328. 

E-mail: jswkxcl@163.com. 

Web site: www.jswkxcl.com. 

Add: no. 5 Donghai road, Haizhou development zone, Lianyungang city, Jiangsu province



What are the methods of use and matters needing attention of plastic template

Your current location: Home >> News >> Industry news

What are the methods of use and matters needing attention of plastic template

Date of release:2019-04-22 Author: Click:

Pvc plastic template is widely used in construction engineering, and pvc plastic template also has many advantages, but there are still some matters needing attention in the use of pvc plastic template. 

Today, Jiangsu Wangke new materials to tell you about the use of pvc plastic template and matters needing attention! 

1. Like the wooden template, it will be shipped to the construction site and stacked in a flat place. 

2. There is no need to apply oil before use. When hoisting, wrap the cable with soft material to prevent damage. 

3. If you need to use different specifications, you can book and reduce the waste of the plate. 

4. When cast-in-place slab, the bottom spacing can be 20 to 30cm, and the beam-column spacing is 50-60CM. 

5. The end hole of the board must be sealed with tape, so that the mortar can not enter the hole, otherwise it is easy to disassemble, and even cause damage to the product. 

6. Nails are hammered in places with small vertical bars and nails are not suspended. 

7. The nail length should not be too long, generally about 30-35MM can, the nail is too long, easy to affect the mold removal.

Pvc plastic template

8. The joint of the two boards shall be sealed with tape to prevent the infiltration of mortar from affecting the demoulding. 

9. When removing the mould, it must be carried out from a small piece at one end, and the template should be removed while removing the support to prevent a large area from falling. 

10. Where the nail is hammered, seal it with tape if you don't use it next time. 

11. Do not make the edges and corners directly hit the ground, at the same time, try to make sense of the ground of the hard construction waste such as nails, waste steel, etc., to prevent the direct fall of the template on the hard construction waste to cause plane damage, affecting the next use. 

12. in the process of mold removal, workers must be required to disassemble from both ends of the scaffolding, fall at the same time, the fall must be kept horizontal, do not let the edges and corners fall vertically to the ground. 

13. The removed plastic building template needs to be cleaned up in time before stacking nails and mortar. 

14. This product is suitable for minus 40 degrees to 70 degrees. 

15. When there is an electric welding operation, the surface of the template can be sprayed with water to prevent a large piece of welding slag from burning the surface. 

The above is the crust foaming template manufacturer-Wangke new material to provide! 

Welcome to inquire!


The address of this article:/en/news/418.html

Key word:Priceofpvcplastictemplate,Pvcplastictemplatemanufacturer

Recently browse:

Crust foaming template

Scan the code and learn more

Contact

Jiangsu Wangke new materials Co.,Ltd

Tel:13141505998/13775442299

Email:jswkxcl@163.com

Web:www.jswkxcl.com

Add:No. 5 Donghai road, Haizhou development zone, Lianyungang city, Jiangsu province

亚游国际ag|亚游首页登录入口

XML 地图 | Sitemap 地图